Chop your Heinie...

...and other hiking related do-it-yourself designs.
User avatar
Skidsteer
Posts: 555
Joined: Fri Aug 17, 2007 2:10 pm
Location: Leisure Acres

Chop your Heinie...

Postby Skidsteer » Tue Sep 04, 2007 7:49 pm

...and still have a rim that adds rigidity and accepts a tight lid. Right! Let’s get down to work:

Get some Luck's microwaveable stew. I’m partial to the chicken & dumplings.

Cut the aluminum rim off with a razor knife. Leave that bit of plastic inside the rim-you’ll need it later.

Turn the rim upside-down, place it on your Heinie, and and chop the pot about an 1/8” above the new rim.

Make 16 evenly spaced cuts down to the new rim, bend the tabs parallel with the top of the pot, and round off the corners of the tabs with your scissors.

Finish bending all the tabs over the new rim with some needle-nose pliers.

Remember the plastic left in the rim? Heat the rim with a pencil torch(a lighter will work in a pinch). The plastic will expand and seal the tabs in place.
Skids

Insanity: doing the same thing over and over again and expecting different results.
Albert Einstein, (attributed)
Image

User avatar
irrationalsolutions
Posts: 1450
Joined: Thu Sep 25, 2008 5:10 am
Location: South Carolina

Re: Chop your Heinie...

Postby irrationalsolutions » Fri Nov 14, 2008 4:29 am

i was trying but you lost me. do you have any pics?
“Do or do not... there is NO try.” Yoda

Luke "Whats in (out) there?" Yoda "Only what you take with you."

Luke "I can’t believe it." Yoda "That is why you Fail.”

User avatar
Skidsteer
Posts: 555
Joined: Fri Aug 17, 2007 2:10 pm
Location: Leisure Acres

Re: Chop your Heinie...

Postby Skidsteer » Fri Nov 14, 2008 11:00 am

irrationalsolutions wrote:i was trying but you lost me. do you have any pics?


Sure thing.

ImageImageImageImageImage
Skids

Insanity: doing the same thing over and over again and expecting different results.
Albert Einstein, (attributed)
Image

User avatar
irrationalsolutions
Posts: 1450
Joined: Thu Sep 25, 2008 5:10 am
Location: South Carolina

Re: Chop your Heinie...

Postby irrationalsolutions » Fri Nov 14, 2008 3:27 pm

thanks
“Do or do not... there is NO try.” Yoda

Luke "Whats in (out) there?" Yoda "Only what you take with you."

Luke "I can’t believe it." Yoda "That is why you Fail.”

User avatar
Skidsteer
Posts: 555
Joined: Fri Aug 17, 2007 2:10 pm
Location: Leisure Acres

Re: Chop your Heinie...

Postby Skidsteer » Fri Nov 14, 2008 4:16 pm

irrationalsolutions wrote:thanks


I mostly use this method nowadays. viewtopic.php?f=17&t=590

Here's how to do it and what you need:

-Cat food can
-Safety opener
-Dremel tool with two bits: a Diamond cut-off wheel and a Sandpaper 'flapwheel'.
-JBWeld

1)Open the can with your safety opener and sand the inside lip of the cat food can and the outer part of the Heineken pot.

2)Poke a hole in the bottom of the can for air relief.

3)Apply a thin, even coat of JBWeld to the inside of the catfood can with your finger.

4)Shove the can onto the Heinie pot as far as it will go. Carefully wipe off the excess epoxy, turn upside down and allow to dry overnight or longer.

5)With the Dremel, cut off the extra can as close to the rim as you can.

6)Switch to the flapwheel and sand the burrs off from the inside of the can working out. This will 'pull' the metal of the Heineken pot back over the rim slightly to lock it in place.
Skids

Insanity: doing the same thing over and over again and expecting different results.
Albert Einstein, (attributed)
Image


Return to “Stove Designs by Skids...”

Who is online

Users browsing this forum: No registered users and 1 guest