Page 5 of 7

Re: RF StarLyte Stove

Posted: Wed Apr 08, 2009 2:02 pm
by zelph
Mister Krabs wrote:
realityguy wrote:
I hope you caught the camo one rather than the pink one... :lol: :lol: :DB:

The one I got was red with a big KOP printed on the side.

There's an idea if they work out, you could come up with a logo and get it printed on there.
I asked if the clear flasks were available wholesale so I could imprint them. Waiting for their answer.
:)

Re: RF StarLyte Stove

Posted: Thu Apr 09, 2009 6:04 pm
by zelph
Here is the collapsable bottle I told you about. I used the shrader valve and it worked well. My wife was due home soon so I was nervous making the videos :mrgreen:


Image
Image
Image

Re: RF StarLyte Stove

Posted: Tue Apr 14, 2009 9:54 pm
by zelph
I got my fuel flasks in today. The ones that Mister Krabs gave us a link to. Tomorrow I'll put together a group of left over parts that I have from this remote fueled stove project. I'll make them available for a modest amount. You'll be able to put together your own remote fueled stove to suite your needs.

Image
Image

Re: RF StarLyte Stove

Posted: Wed Apr 15, 2009 4:46 pm
by zelph
OK, here ya go. I have parts available for four (4) kits to make your own remote feed stove. The amount of kits I have is governed by how many funnels I had available. :D

This is what you get:

1- 250ml IV bag (new)

1- IV bag tube feed kit (contains the drip/feed regulator plus tubing)(new)

1- flask (new)

1- brass 90 degree fitting with soldered 1/8" tube (new)

2- nickle plated nuts for the above brass fitting (new)

1- funnel for filling IV bag (new)

3 feet of Tygon brand tubing 1/8 inside diameter (new)

1- hose clamp for Tygon tubing (new)

Cost: $17.00 + $3.00 shipping = $20.00

All new parts.


Note: brass fitting can be drilled out to receive fiberglass wick material. Make a VD stove :DB:

Image

Re: RF StarLyte Stove

Posted: Wed Apr 15, 2009 5:07 pm
by hoz
A "VD" stove??? Oh you so BAD!

Put me down for one.

I'll paypal you tonight.

Re: RF StarLyte Stove

Posted: Wed Apr 15, 2009 7:58 pm
by zelph
hoz wrote:A "VD" stove??? Oh you so BAD!

Put me down for one.

I'll paypal you tonight.
:mrgreen: I'm Bad!!! See me be bad :o

All you visionary people out there will be able to see this kit is not limited to alcohol. Think remote canister!!!! some of the parts in there are doable. They can get you started. There's 3 feet of hose there, only need 1.5 ;)

Re: RF StarLyte Stove

Posted: Mon Apr 20, 2009 10:56 pm
by Irvingdog
zelph wrote: 1- brass 90 degree fitting with soldered 1/8" tube (new)

2- nickle plated nuts for the above brass fitting (new)
Maybe I missed it. Where is this piece from? I cruised the hardware stre and found a brass elbow with a barbed fitting on one end, but the one I found is a bigger and WAY heavier.

Re: RF StarLyte Stove

Posted: Tue Apr 21, 2009 1:56 pm
by zelph
Irvingdog wrote:
zelph wrote: 1- brass 90 degree fitting with soldered 1/8" tube (new)

2- nickle plated nuts for the above brass fitting (new)
Maybe I missed it. Where is this piece from? I cruised the hardware stre and found a brass elbow with a barbed fitting on one end, but the one I found is a bigger and WAY heavier.
I got mine at an ACE hardware. I soldered the 1/8 o.d. brass tube onto the barbed end. I purchased all they had. The hardware store seems to be cutting way back and may be getting ready to close their doors. Shelves are not being restocked.

The nuts are from the electrical dep. They are used in conjunction with a threaded extension for hanging a small fixture from the ceiling.

HOZ, the funnel goes into the white capped port. The other is a spare port if needed. Follow the directions on the IV assembly package to operate with only the iv set. Adjust flow with the set untill you get familiar with the roller adjuster. Make permanent scribed lines on the roller housing according to drops. (simmer, full bore etc.)

Re: RF StarLyte Stove

Posted: Tue Apr 21, 2009 3:01 pm
by hoz
I thought the brown port was for injecting medicines into the IV bag. At least I've seen the nurses do it that way from time to time.

Re: RF StarLyte Stove

Posted: Tue Apr 21, 2009 4:11 pm
by Irvingdog
Could I trouble you for a close-up image of it?