TeePee
-
- Posts: 1450
- Joined: Thu Sep 25, 2008 5:10 am
- Location: South Carolina
Re: TeePee
great looking setup! i like it!
“Do or do not... there is NO try.” Yoda
Luke "Whats in (out) there?" Yoda "Only what you take with you."
Luke "I can’t believe it." Yoda "That is why you Fail.”
Luke "Whats in (out) there?" Yoda "Only what you take with you."
Luke "I can’t believe it." Yoda "That is why you Fail.”
Re: TeePee
Very, very nice.....looks like the new one is going to pump out the btu's no problem. Did you use stainless steel stove pipe for the tube section?
Really nice looking stove and wigwam.....fire that baby up over the weekend and show us som HOT photos. We want to see bare ground under the stoves belly from the heat. Shorten the legs so the radiant heat is lower to the ground so it will be absorbed and radiate it during the night.
Really nice looking stove and wigwam.....fire that baby up over the weekend and show us som HOT photos. We want to see bare ground under the stoves belly from the heat. Shorten the legs so the radiant heat is lower to the ground so it will be absorbed and radiate it during the night.
http://www.woodgaz-stove.com/
- Ridgerunner
- Posts: 5278
- Joined: Wed Sep 19, 2007 9:08 pm
- Location: SW, Ohio
- Contact:
Re: TeePee
Nice setup. Do you have a stove flap for the opening in the tent? I like the tent also. What is your review on that teepee?
"Many of lifes failures are people who did not realize how close they were to success when they gave up".....Thomas Edison
"Live Life....Love Life....Ask More !
"Live Life....Love Life....Ask More !
-
- Posts: 36
- Joined: Thu Mar 06, 2008 10:35 pm
- Location: CNY
Re: TeePee
Nope, it's just HVAC ducting. It's heavy enough that it'll probably last a number of seasons, light enough that we barely notice it dragging along in a pulk, and easy to work with very simple hand tools.zelph wrote: Did you use stainless steel stove pipe for the tube section?
The legs will get cut a little shorter, but it's nice to leave some space under the stove. When gathering wood in the winter, it's inevitably got ice on it. Putting the next load of wood under the stove while the first is still burning is an easy way to melt the snow and ice off. That way the new wood won't cool the stove down too much when it's loaded in.zelph wrote: Shorten the legs so the radiant heat is lower to the ground so it will be absorbed and radiate it during the night.
If by storm flap you mean a covering for the hole where the chimney goes through the roof, then yes, there is one. Actually, it's a welder's blanket that's sewn in there now. No melting that one.Ridgerunner wrote:Do you have a stove flap for the opening in the tent? I like the tent also. What is your review on that teepee?
The teepee itself is fine. When winter camping with a woodstove, there is sufficient room in it to sleep 4 adults. The woodstove and the center pole are bigger space eaters than you'd imagine. One of the unexpected features about the tent is that the floor is detachable. It saved us the trouble of cutting it out.
Last night we had the very first burn in the new stove, not in the tent though, just in my buddies driveway.

Here's the new one next to the old one. Big difference.

Some of the wood laying in my buddies woodpile had started to go punky and didn't want to burn that well. Enter the leaf blower. Nothing some force feeding couldn't fix!

Some time over the next couple weeks we will set up the tent and give the stove a true workout. Hopefully deep in some forest in the Adirondacks.
Ordin
They speak of my drinking, but never of my thirst...
- Ridgerunner
- Posts: 5278
- Joined: Wed Sep 19, 2007 9:08 pm
- Location: SW, Ohio
- Contact:
Re: TeePee
Nicely done Ordin. That should keep you nice and toasty in your teepee!
Daren made a nice woodburner for an island cabin that he kayaks to. There are some pics on this site somewhere.

"Many of lifes failures are people who did not realize how close they were to success when they gave up".....Thomas Edison
"Live Life....Love Life....Ask More !
"Live Life....Love Life....Ask More !
-
- Posts: 5948
- Joined: Tue Feb 24, 2009 2:20 am
- Location: slightly north of Seattle,WA
Re: TeePee
Is it feasible to offset the pole from the center position to save room..or use 2-3 poles that go to the outside edges instead?I would think a 3 pole setup with the stove going through the middle of a section between two poles could get you 2/3rds of the tent back.Are you going to add a metal heatshield to the back side of the stove to protect the tent there?Leaving a 1" air gap between the actual stove and shield makes quite a difference in the heat factor going towards the tent..and it could be made from pretty lightweight metal sheeting.
As far as losing the floor..couldn't you save half or a large portion of it?
As far as losing the floor..couldn't you save half or a large portion of it?
The views and opinions expressed by this person are his own and not the general consensus of others on this website.Realityguy
Re: TeePee
Nice, nice, nice!!!!!
I like it
I just had an idea. Make the stove and flu the same diameter. Put a damper in the flu to regulate heat.
Radiant heat maximus....why does this sound too easy????? The pulk can carry it so what the heck

I just had an idea. Make the stove and flu the same diameter. Put a damper in the flu to regulate heat.
Radiant heat maximus....why does this sound too easy????? The pulk can carry it so what the heck

http://www.woodgaz-stove.com/
-
- Posts: 36
- Joined: Thu Mar 06, 2008 10:35 pm
- Location: CNY
Re: TeePee
Sounds feasible enough. We'll have to give it a try. Thanks for the idea!realityguy wrote: Is it feasible to offset the pole from the center position to save room..or use 2-3 poles that go to the outside edges instead?I would think a 3 pole setup with the stove going through the middle of a section between two poles could get you 2/3rds of the tent back.
The metal heatshields already exist. This was the prototype on testing day. The heatshields were INCREDIBLY effective at keeping heat off of the tent and reflecting it back inside. Putting your hand between the heatsheild and the outer tent wall really felt cool, almost cold. It was a key addition.realityguy wrote: Are you going to add a metal heatshield to the back side of the stove to protect the tent there?Leaving a 1" air gap between the actual stove and shield makes quite a difference in the heat factor going towards the tent..and it could be made from pretty lightweight metal sheeting.

Sorry, no pics of the final pieces in action. When we take this thing for a shakedown cruise I'll take a bunch then.
Losing the floor isn't really a big deal. In winter, the boots really only come off when the feet are ready to go hide in the sleeping bag anyhow. The floor would just end up being a muddy, wet, and ultimately icy mess. Good riddance.realityguy wrote: As far as losing the floor..couldn't you save half or a large portion of it?
Ordin
They speak of my drinking, but never of my thirst...
-
- Posts: 36
- Joined: Thu Mar 06, 2008 10:35 pm
- Location: CNY
Re: TeePee
Good idea. However, there's limited space in the pulk (although I do have two rigged train-style) and making the stove system too big would take up lots of that precious space that's reserved for beer and bratwursts.zelph wrote:Nice, nice, nice!!!!!I like it
I just had an idea. Make the stove and flu the same diameter. Put a damper in the flu to regulate heat.
Radiant heat maximus....why does this sound too easy????? The pulk can carry it so what the heck

From a solo trip to an Adirondack lean-to for a few days, the week before Christmas...

Ordin
They speak of my drinking, but never of my thirst...
-
- Posts: 5948
- Joined: Tue Feb 24, 2009 2:20 am
- Location: slightly north of Seattle,WA
Re: TeePee
I would think a sideways stove with a secondary half circle of metal bolted(to the stove with "[" shaped brackets) 1" out covering the back would make a good heat shield taking up minimal room within the tent..plus the half circle will draw cold air from underneath through the warmer section behind the stove(in between it and the heat shield) and push it out the front on top with convection..Of course you need to leave some section uncovered for placing pots on top(middle section for maximum heat?).The heatshield could be mounted with small brackets and bolts/wingnuts,rolled inside the stove when packing9along with the chimney)... and taking up very little storage against the back wall inside the stove.
Normal wood stove piping does have available 1/2 pipe rear shields for the stove pipe also to protect walls from damage and to reduce clearances to combustible areas..same idea..rolled inside the pipe for travel.
A little bit of sheet metal might add minimal weight but give you a lot more heat/room in the teepee when you need it...just a thought...But that's just me..I'm a McGyver-type person...
................. 
Normal wood stove piping does have available 1/2 pipe rear shields for the stove pipe also to protect walls from damage and to reduce clearances to combustible areas..same idea..rolled inside the pipe for travel.
A little bit of sheet metal might add minimal weight but give you a lot more heat/room in the teepee when you need it...just a thought...But that's just me..I'm a McGyver-type person...


The views and opinions expressed by this person are his own and not the general consensus of others on this website.Realityguy